JOHN DEERE

WE ARE NO LONGER

MANUFACTURING

JOHN DEERE BLOCKS OR HEADS

Manifolds still available

JOHN DEERE

RETAINERS AND LOCKS

Click Here for Pricing

JOHN DEERE

FLYWHEEL WASHER

Grade 8 Bolt included

FW-63 Utilizes a 5/8 Bolt

FW-75 Utilizes a 3/4 Bolt

**Reusable**

Billet Steel

Flywheel Lock Nut

w/Reusable Lock Washer

Wrench available separately 

Nut and Lock Washer $65

Wrench $40

replaces part# A3312R

fits

Late A thru 730 Diesel

Billet aluminum main bearing housings for John Deere 70

MF1229R Main bearing housing clutch side includes finished bearing, seals and bronze thrust washer shown

(thrush washer will need thickness adjusted)

 weighs 3.5# less than stock

$1200.00 

MF1230R Main bearing housing flywheel side uses stock thrust washers

includes finished bearing

  weighs 7.8# less than stock

$775.00

Billet aluminum main bearing housings for G John Deere

MF1063R Main bearing housing clutch side includes finished bearing and bronze thrust washer.

(thrush washer will need thickness adjusted)

weighs 10.6# less than stock

$845.00

MF770R Main bearing housing flywheel side

includes finished bearing and bronze thrust washer.

 uses JD#A4398R thrust washer on outside and included bronze thrust washer on inside

 weighs 18.8# less than stock with oil slinger housing shown below

$1350.00 

# MF77RIK aluminum oil slinger housing with lip seal

$360.00

Billet aluminum main bearing housing for A John Deere

MA4393R Main bearing housing flywheel side uses stock thrust washers

includes finished bearing

  weighs 6.2# less than stock

$ Call

Auxiliary thrust washer for clutch side of crankshaft currently available for A, G & 70 John Deere  $60.00

JOHN DEERE PISTONS

High Compression for JD-D

+ .125" and .250"

1.187" Taller than Stock w/sparkplug notch

Stock Replacement for JD-LA 

+ .040" = 3.540 bore

Stock Replacement for JD-B

to serial 59,999

4.250" bore Std.  & + .060"  & +.150

John Deere A & G

Crankcase

Support

John Deere Head Gaskets

Head Gasket 6.55 Bore x .063 Thick

works for G  ser# 7100 and up All Fuel applications

 #756HG - $105.00

Early G to ser# 7099, Stock Replacement Head Gasket

#MF55R - $115.00

Styled A  Stock Replacement Head Gasket $47.00

Unstyled A Head Gasket 5.780 Bore x .063 compressed thickness. $115.00

Above head gasket available in a valve grind set.

John Deere "G" head parts:

Stock Replacement John Deere "G" Valve Springs - ALL

80#@3.200, 135#@2.700, 155#@2.500, 175#@2.300, CB@1.950

#MF53R - $60.00 a set

Stock Replacement John Deere "G" Valve Guides

Fits serial 13000 up (will fit below #'s by shortening guide 1/2")

#MF727R - $60.00 set

G Flathead Head Stud Kit "ALL"

OE part no. F56R 6.750" long - MF56RK Murphys Stud 7-3/8" long

NOTE! Murphys Studs Do Not Have Interference Fit on Block End (WILL REQUIRE THREAD SEALER)

#MF56RK - $185.00

 Pushrod Kit for Flathead on a Styled Block

Includes Special Adjusting Screws

#MF126RSK - $160.00

John Deere "G" Manifolds:

"G" Manifold has been redesigned for water pipe clearance, October 09.

• Three styles available: 
• Large runner to fit Murphy's heads
• Small runner to fit John Deere heads. 

• Duplex manifolds to use two-barrel carburetors from JD 50-730 tractors

Manifolds include 2 gaskets and grade 8 fasteners..

• JD-G Manifold-Large    (To fit Murphy's Head)   $340.00

• JD-G Manifold-Small     (To fit John Deere Head) $340.00

• JD-G Manifold-Duplex-Large (To fit Murphy's Head) $475.00

• JD-G Manifold-Duplex-Small (To fit John Deere Head) $475.00

JOHN DEERE STYLED A PARTS

"Styled A" Parts (Fit tractors SN: 488000 and UP, unless noted): 

John Deere Styled "A" Manifolds:

"A" Manifold has been redesigned for water pipe clearance, October 09.

• Fits tractor serial numbers 488000-584000
• Fits tractor serial number 584000 & up by changing exhaust pipe. NOTE mounting flange difference.

Manifolds include 2 gaskets and grade 8 fasteners

• JD-SA Manifold-Large (To fit Murphy's Head)  $340.00
• JD-SA Manifold-Small (To fit John Deere Head) $340.00
• JD-SA Manifold-Duplex-Large (To fit Murphy's Head) $475.00
• JD-SA Manifold-Duplex-Small (To fit John Deere Head) $475.00

JOHN DEERE UNSTYLED "A" PARTS

"Unstyled A" Parts (Fit tractors SN: 410000 to 487999, unless noted)  

Unstyled A Head Gasket 5.780 Bore x .063 compressed thickness.

$115

Above head gasket available in a valve grind set.

Unstyled "A" Manifolds:

"NEW"

Small Port version to match Stock Head

* Includes grade 8 bolts and 2 gaskets *

• JD-USA Manifold                               $340.00